NewF&I Power Session: $199 launch price for the first 10 clientsContactcontact@dealershipfibootcamp.com
All resourcesInside the office

Buy rate vs. sell rate: how dealer reserve works

Where a big part of F&I income comes from, how the math works, the limits that apply, and how to stay fair and consistent with every customer.

Camila VenegasUpdated November 20265 min read
Two men in blazers at a table in a car dealership, one signing a document
The rate on the contract the customer signs can be different from the rate the lender approved. Photo: Vitaly Gariev / Unsplash
The short answer

The buy rate is the interest rate a lender approves for the customer. The sell rate (contract rate) is the rate the customer actually signs at. When the lender allows it, the dealer can set the contract rate above the buy rate, and the lender pays the dealer part of the extra interest. That payment is called dealer reserve or finance reserve. Lenders and some states cap how much the rate can be marked up, often around 2 to 2.5 percentage points.

Why new F&I managers get confused about rate

A customer gets approved at one rate, signs at another, and the new F&I manager isn’t sure what just happened or whether it was allowed. In my 17 years in the car business, rate is the topic new managers understand least, and it’s also where a lot of compliance risk lives.

Here’s how it works, in plain English, so you can explain it, calculate it and handle it the right way.

What is the buy rate?

When you submit a credit application, the lender reviews it and approves the deal at a rate based on the customer’s credit, the term, the vehicle and the amount financed. That approved rate is the buy rate. It’s the lender’s price for the loan.

What is the sell rate?

The sell rate, also called the contract rate, is the APR on the retail installment contract the customer signs. Because the dealer is arranging the financing, many lenders let the dealer set the contract rate above the buy rate, up to a limit in the dealer agreement.

Rate markup = sell rate − buy rate. Example: buy rate 6.9%, sell rate 8.4%, markup 1.5 points.

How is dealer reserve calculated?

A calculator and a pen on a printed page
Markup is the difference between the contract rate and the lender’s buy rate. Photo: Aaron Lefler / Unsplash

The lender pays the dealer part of the extra interest the markup creates. Each lender sets its own formula: some pay a share of the extra interest as a lump sum when the deal funds, and some pay a flat fee instead of any markup. The exact amount depends on the amount financed, the term and the lender’s split, so use the lender’s reserve calculation or your menu software rather than guessing.

Reserve is often part of an F&I manager’s commission. It can also be charged back if the loan pays off early. Read how F&I pay plans work to see how that affects your check.

How much can a dealer mark up the rate?

There’s no single national number, but limits are common:

  • Lender caps: most dealer agreements set a maximum markup. Caps around 2 to 2.5 points, with lower caps on longer terms, became common after lender settlements in the early 2000s, according to F&I and Showroom.
  • State caps: some states limit markup by law. California, for example, caps it at 2.5 points on contracts of 60 months or less and 2 points on longer ones.
  • State maximum rates: many states also set a maximum finance charge rate. The contract rate can’t go above it, no matter what the lender allows.
  • Flat-fee programs: some lenders and special-rate programs allow no markup at all.

Always check the lender’s program sheet and your state’s rules before you set a rate.

How do you handle rate fairly and legally?

  • Use a consistent, written policy. Mark up rates the same way for every customer. Different markups for similar customers can create fair lending risk under the Equal Credit Opportunity Act.
  • Document legitimate reasons for any exception, such as matching a competing offer.
  • Never misstate the rate. Don’t tell a customer the contract rate is “the rate the bank gave you” if it isn’t.
  • Disclose clearly. The APR and finance charge on the contract are the customer’s numbers. Walk them through those numbers honestly.
  • Follow your store’s compliance process and the lender’s dealer agreement every time.

Want to see how rate fits into the whole deal? Read what an F&I manager does all day and how DTI and PTI decide approvals.

Leases price the rate differently. Read lease vs. finance: how F&I explains the difference.

Frequently asked questions

Is dealer reserve legal?

Yes, when it stays within the lender’s agreement and state law, and is applied consistently. Rules vary by state and lender, so always follow your store’s written policy.

Does the customer see the buy rate?

Usually not. The customer signs a contract showing the APR and finance charge. Be honest if a customer asks how the rate was set.

What is a flat fee instead of reserve?

Some lenders pay the dealer a fixed amount per deal instead of allowing a markup, often on special or promotional rates.

Can reserve be charged back?

Yes. If a loan pays off or refinances early, the lender may take back part of the reserve, depending on the dealer agreement.

This article is general education, not legal advice. Markup limits, maximum rates and reserve formulas vary by lender and state and can change. Follow your lender agreements, state law and dealership policy.

Keep reading

Want to understand lender math before your first day?

The F&I Power Session walks you through rate, reserve and deal structure, one on one with an experienced finance manager.

Claim a launch seatFree brochure (PDF)
Scroll to Top